HM Medical Clinic

Even if Viagra is not needed, it is possible that the doctor will be able to determine the etiology of erectile dysfunction and prescribe appropriate treatmen https://vgraustralia.net it doesn't pay to forget about sexual activeness even at the first sings of malfunction.

Safety data sheet


IKOpro PU Insulation Adhesive Revision date: 12/02/2013
SAFETY DATA SHEET

IKOpro PU Insulation Adhesive

This Safety Data Sheet contains information concerning the potential risks to those involved in handling,
transporting and working with the material, as well as describing potential risks to the consumer and the
environment. This information must be made available to those who may come into contact with the material or
are responsible for the use of the material. This Safety Data Sheet is prepared in accordance with formatting
described in the REACH Regulation (EC) No 1907/2006, and described in CLP Regulation (EC) No 1272/2008.
SECTION 1: Identification of the substance/mixture and of the company/undertaking
1.1
Product identifier
IKOpro PU Insulation Adhesive

Relevant identified uses of the substance or mixture and uses advised against
Adhesive
Details of the supplier of the safety data sheet
IKO PLC
Appley Lane North
Appley Bridge, Wigan
Lancashire WN6 9AB
Tel: 0844 412 7225
Fax: 0844 412 7205
Emergency telephone number
Tel: 0844 412 7228 (available 08:30 to 17:00 weekdays)


SECTION 2: Hazards Identification

2.1 Classification of the substance or mixture
Classification under CHIP:

Xn: R20; Xi: R36/37/38; Xn: R40; Sens.: R42/43; Xn: R48/20
Most important adverse effects:

Harmful by inhalation. Irritating to eyes, respiratory system and skin. Limited evidence of a carcinogenic effect. May cause sensitisation by inhalation and skin contact. Harmful: danger of serious damage to health by prolonged exposure through inhalation.
2.2 Label elements

Label elements under CHIP:

Hazard symbols:
Harmful.

Risk phrases:
R20: Harmful by inhalation.
R36/37/38: Irritating to eyes, respiratory system and skin. Page 1 of 8
IKOpro PU Insulation Adhesive Revision date: 12/02/2013 R40: Limited evidence of a carcinogenic effect. R42/43: May cause sensitisation by inhalation and skin contact. R48/20: Harmful: danger of serious damage to health by prolonged exposure through inhalation.
Safety phrases:
S23: Do not breathe vapour. S36/37: Wear suitable protective clothing and gloves. S45: In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible). S63: In case of accident by inhalation, remove casualty to fresh air and keep at rest.
Precautionary phrases:
Contains isocyanates. See information supplied by the manufacturer.
Contains benzoyl chloride. May produce an allergic reaction.
2.3 Other hazards
PBT: This product is not identified as a PBT substance.

SECTION 3: Composition / information on ingredients
3.2 Mixtures
Hazardous ingredients:
DIPHENYLMETHANE DIISOCYANATE (ISOMERS AND HOMOLOGUES)

EINECS

CHIP Classification
CLP Classification
Carc. 2: H351; Acute R36/37/38; Xn: R40; Tox. 4: H332; Eye Sens.: R42/43; Xn: Irrit. 2: H319; STOT SE 3: H335; Skin Irrit. 2: H315; Resp. Sens. 1: H334; Skin Sens. 1: H317; STOT SE 2: H371; STOT RE 2: H373

SECTION 4: First Aid Measures
4.1. Description of first aid measures
Skin contact:
Remove all contaminated clothes and footwear immediately unless stuck to skin.
Remove from skin with paper or towel. Wash effected area thoroughly with soap and water. Seek medical advice if symptoms persist.
Eye contact:

Bathe the eye with running water for 15 minutes. Transfer to hospital for specialist
examination.
Ingestion:
Do not induce vomiting. If conscious, give half a litre of water to drink immediately. Transfer to hospital as soon as possible.
Inhalation:
Remove casualty from exposure ensuring one's own safety whilst doing so. Obtain
medical help if there is difficulty breathing.
Page 2 of 8
IKOpro PU Insulation Adhesive Revision date: 12/02/2013 I
4.2. Most important symptoms and effects, both acute and delayed
Skin contact:
There may be irritation and redness at the site of contact. Onset of symptoms may be
Eye contact: There may be irritation and redness.
Ingestion:
Nausea and stomach pain may occur. There may be vomiting.
Inhalation:
Exposure may cause coughing or wheezing. There may be congestion of the lungs causing severe shortness of breath. Onset of symptoms may be delayed. Delayed / immediate effects: No data available.
4.3. Indication of any immediate medical attention and special treatment required
Immediate / special treatment:
Show this safety data sheet to the doctor in attendance.
SECTION 5: Firefighting Measures
5.1
Extinguishing media:

Extinguishing media:
Carbon dioxide. Alcohol or polymer foam. Dry chemical powder.
5.2
Special hazards arising from the substance or mixture

Exposure hazards:
In combustion emits toxic fumes.
5.3
Advice for fire fighters

Advice for fire-fighters:
Wear self-contained breathing apparatus. Wear protective clothing to prevent contact
with skin and eyes.
SECTION 6: Accidental Release Measures
6.1
Personal precautions, protective equipment and emergency procedures

Personal precautions:
Mark out the contaminated area with signs and prevent access to unauthorised
personnel. Turn leaking containers leak-side up to prevent the escape of liquid. Refer to section 8 of SDS for personal protection details. Environmental precautions

Environmental precautions:
Do not discharge into drains or rivers. Contain the spillage using bunding.
6.3
Methods and materials for containment and clearing up

Clean-up procedures: Absorb into dry earth or sand. Neutralise with dilute hydrochloric acid. Nuetralise with
water containing 1% wetting agent To avoid build up of pressure due to the evolution of carbon dioxide, do not seal containers until fully reacted. References to other sections

Refer to Section 8 of SDS. Refer to section 13 of SDS
Page 3 of 8
IKOpro PU Insulation Adhesive Revision date: 12/02/2013
SECTION 7: Handling and Storage
7.1 Precautions for safe handling
Handling requirements:
Ensure there is sufficient ventilation of the area. Avoid direct contact with the
substance.
7.2 Conditions for safe storage, including any incompatibilities
Storage conditions:
Store in cool, well ventilated area. Keep container tightly closed.
Suitable packaging: Must only be kept in original packaging.
7.3 Specific end use(s): No special requirement

SECTION 8. Exposure Controls/Personal Protection
8.1
Control parameters

Workplace exposure limits:

Respirable dust
8 hour TWA
15min STEL
8 hour TWA
15min STEL

Hazardous ingredients:
DIPHENYLMETHANE DIISOCYANATE (ISOMERS AND HOMOLOGUES)
Workplace exposure limits:

Respirable dust
8 hour TWA
15min STEL
8 hour TWA
15min STEL
DNEL/PNEC Values

DNEL / PNEC:
No data available.
8.2

Exposure controls
Engineering measures:
Ensure there is exhaust ventilation of the area. Respiratory protection:
In case of insufficient ventilation wear suitable respiratory equipment. If exposure levels are likely to be exceeded, use a full face mask fitted with an organic AXP3 filter for short term low level exposures. For long term or high level exposures, compressed airline breathing apparatus should be used. Hand protection:
Avoid skin contact. For repeated exposure use Viton or 4H chemical gloves for low exposure use nitrile gloves. The user has a legal duty to carry out a COSHH risk assessment to determine the correct glove.
Eye protection:


Skin protection:

Wear protective work clothing sufficient to avoid skin contact. Wash hands regularly, before breaks and at the end of the working day.
Environmental:
No special requirement. Page 4 of 8
IKOpro PU Insulation Adhesive Revision date: 12/02/2013
SECTION 9: Physical and Chemical Properties
9.1
Information on basic physical and chemical properties
Characteristic odour Evaporation rate: Slow
Oxidising:

Non-oxidising (by EC criteria) Solubility in water: Reacts with water.
Viscosity:

Flash point°C: >200
Autoflammability°C: >400
Vapour pressure: <0.00001hPa
Relative density: 1.12
9.2 Other information
No data available
SECTION 10: Stability and Reactivity
10.1 Reactivity
Stable under recommended transport or storage conditions.
10.2 Chemical stability
Stable under normal conditions.
10.3 Possibility of hazardous reactions
Hazardous reactions will not occur under normal transport or storage conditions.
10.4 Conditions to avoid
Heat. Moist air.
10.5 Incompatible materials

Materials to avoid: Water. Strong acids. Strong bases.
10.6
Hazardous decomposition products
In combustion emits toxic fumes.
SECTION 11: Toxicological Information

The information below may not be consistent with the material classification in Section 2 if specific
ingredient classifications are mandated by a competent authority. In addition, toxicological data on
ingredients may not be reflected in the material classification and/or the signs and symptoms of
exposure, because an ingredient may be present below the threshold for labelling, an ingredient may
not be available for exposure, or the data may not be relevant to the material as a whole.
11.1 Information on toxicological effects

Toxicity values:
Route

Species Test
LD50 >10000 mg/kg Page 5 of 8
IKOpro PU Insulation Adhesive Revision date: 12/02/2013 Relevant effects for mixture:
Effect

Acute toxicity (harmful) Hazardous: calculated Hazardous: calculated Hazardous: calculated Repeated dose toxicity Hazardous: calculated
11.2 Symptoms/routes of exposure
Skin contact:
There may be irritation and redness at the site of contact. Onset of symptoms may be

Eye contact: There may be irritation and redness.
Ingestion:
Nausea and stomach pain may occur. There may be vomiting.
Inhalation:
Exposure may cause coughing or wheezing. There may be congestion of the lungs causing severe shortness of breath. Onset of symptoms may be delayed.
Delayed / immediate effects:
No data available.

Other information:
Not applicable.
SECTION 12: Ecological Information

12.1
Toxicity

Ecotoxicity values:

(Brachydanio rerio) Sludge Persistence and degradability
Biodegradable in part only.
12.3
Bioaccumulative potential
No data available.

12.4

Mobility in soil
Reacts with water to form an insoluble polyurea. Do not discharge in to natural waters without pre-treatment.
12.5
Results of PBT and vPvB assessment
PBT identification: This product is not identified as a PBT substance.

12.6

Other adverse effects
No data available.


Page 6 of 8
IKOpro PU Insulation Adhesive Revision date: 12/02/2013 SECTION 13: Disposal Considerations
13.1
Waste treatment methods

Disposal operations:
Wet waste: Arrange for disposal by a licenced waste disposal company
Disposal of packaging:
Arrange for disposal by a licenced waste disposal company The user's attention is drawn to the possible existence of regional or national regulations regarding disposal.
SECTION 14: Transport Information
Transport class:
This product does not require a classification for transport.
SECTION 15: Regulatory Information
15.1
Safety, health and environmental regulations/legislation specific for the substance or mixture

Specific regulations:
This product is classifed as a mixture. CLP classification for information only. Persons
already sensitised to diisocyanates may develop allergic reactions when using this product. Persons suffering from asthma, eczema or skin problems should avoid contact, including dermal contact, with this product. This product should not be used under conditions of poor ventilation unless a protective mask with an appropriate gas filter (i.e. type A1 according to standard EN 14387) is used. Chemical Safety Assessment

Chemical safety assessment:
A chemical safety assessment has not been carried out for the substance or
the mixture by the supplier.
SECTION 16: Other Information

This safety data sheet is prepared in accordance with Commission Regulation (EU) No 453/2010.
* indicates text in the SDS which has changed since the last revision.
Phrases used in s.2 and 3:
H315
Causes skin irritation. May cause an allergic skin reaction. Causes serious eye irritation. Harmful if inhaled. May cause allergy or asthma symptoms or breathing difficulties if inhaled. May cause respiratory irritation. Suspected of causing cancer <state route of exposure if it is conclusively proven that no other routes of exposure cause the hazard>. May cause damage to organs <or state all organs affected, if known> through prolonged or repeated exposure <state route of exposure if it is conclusively proven that no other routes of exposure cause the hazard>. Harmful by inhalation. Irritating to eyes. Irritating to respiratory system. Irritating to skin. Limited evidence of a carcinogenic effect. May cause sensitisation by inhalation. May cause sensitisation by skin contact. Harmful: danger of serious damage to health by prolonged exposure through inhalation.
Legal disclaimer:
The above information is believed to be correct but does not purport to be all inclusive and
shall be used only as a guide. This company shall not be held liable for any
damage resulting from handling or from contact with the above product.
Page 7 of 8


IKOpro PU Insulation Adhesive Revision date: 12/02/2013

IKO PLC

Literature Enquiries
Tel: 0844 412 8554
E-Mail Website: www.ikogroup.co.uk
Sales Support
Appley Lane North, Appley Bridge, Wigan, Lancashire WN6 9AB
Tel: 0844 873 1062 Fax: 0844 873 1067 E-Mail:
Technical & Design Services
Appley Lane North, Appley Bridge, Wigan, Lancashire WN6 9AB Tel: 0844 412 7228 Fax: 0844 412 7229 E-Mail: [email protected] Whilst every care is taken to see that the information given in this literature is correct and up to date it is not intended to form part of any contract or give rise to any collateral liability, which is hereby specifically excluded. Intending purchasers of our materials should therefore verify with the company whether any changes in our specification or application details or otherwise have taken place since this literature was issued. Company Registered in England No. 2678296 – Registered Office: Appley Lane North, Appley Bridge, Wigan, Lancashire, WN6 9AB Page 8 of 8

Source: http://www.ikogroup.co.uk/SiteFiles/Content/MediaLibrary/Documents/Data%20Sheets/IKOpro-PU-Insulation-Adhesive-MSDS-04-13.pdf

Microsoft word - uso de antimicrobianos en animales de consumo2004new.doc

162 ISSN 1014-1200 FAO PRODUCCIÓN Y SANIDAD ANIMAL USO DE ANTIMICROBIANOS EN ANIMALES DE CONSUMO incidencia del desarrollo de resistencias en salud pública FAO PRODUCCIÓN Y SANIDAD ANIMAL USO DE ANTIMICROBIANOSEN ANIMALES DE CONSUMO incidencia del desarrollo de resistencias en salud pública J. O. ErrecaldeFacultad de Ciencias Veterinarias,Universidad Nacional de La Plata, Argentina

Alb_esp

Condiciones generales para el suministro de maquinaria y repuestos 1. Generalidades 1.1 El contrato se considerará concluido al recibir la confirmación por escrito del proveedor estipulando su aceptación del pedido (confirmación del pedido). Ofertas que no contienen un plazo de aceptación se entienden sin compromiso.